List of available copper and fiber testing videos
The following copper and fiber test videos are also available without registration:
DSX CableAnalyze
- DSX-101 Setting up for aCategory 5e Permanent Link test
- DSX-102 Setting a reference
- DSX-103 Setting up for a two pair Category 5e Permanent Link test
- DSX-104 Shield integrity
- DSX-105 Worst case margin vs. worst case value
- DSX-106 Modified Single Connector Permanent Link
- DSX-107 NVP - Nominal Velocity of Propagation
- DSX-108 NEXT fails due to a poor termination
- DSX-109 NEXT fails on a short link
- DSX-110 Return Loss fails due to cable (example #1)
- DSX-111 Return Loss fails due to cable (example #2)
- DSX-112 Return Loss fails due to water in the cable
- DSX-113 NEXT fails due to cable
- DSX-114 Lubricant caused Insertion Loss to fail
- DSX-115 Poor balance resulted in a 1000BASE-T switch operating at 100BASE-TX
- DSX-116 The 3 dB rule
- DSX-117 The 4 dB rule
- DSX-118 10% rule for length
CertiFiber Pro 光纤认证测试仪
- CFP-101 Automated Fiber Inspection
- CFP-102 Custom fixed loss limits in the CertiFiber Pro
- CFP-103 Custom connector/splice/fiber loss limits in the CertiFiber Pro
- CFP-104 Single fiber testing with the CertiFiber Pro
OptiFiber Pro
- OFP-101 Unpacking, setting up and making a measurement
- OFP-102 Clearing the memory and all settings in your OptiFiber
- OFP-103 Attaching the straps on your OptiFiber Pro
- OFP-104 OptiFiber Pro test limits
- OFP-105 OptiFiber Pro launch only compensation
- OFP-106 OptiFiber Pro launch plus tail compensation
- OFP-107 OptiFiber Pro Auto vs Manual OTDR mode
- OFP-108 OptiFiber Pro Project Management
- OFP-109 OptiFiber Pro EventMap
- OFP-110 Putting the OptiFiber in Full Data Mode (Only do this if instructed by the Fluke Networks Technical Assistance Center)
FiberInspector
DTX CableAnalyzer
- DTX-CU-103 Certifying a Category 6A Patch Cord
- DTX-CU-104 Certifying an M12 Patch Cord
- DTX-CU-105 Recover deleted results from a DTX CableAnalyzer
- DTX-CU-201 Diagnosing a Category 6 NEXT failure # 1 (Badly Terminated Permanent Link)
- DTX-CU-202 Diagnosing a Category 6 NEXT failure # 2 (Cable Issue)
- DTX-CU-203 Diagnosing a Category 6 Return Loss failure # 1 (Cable Issue)
- DTX-CU-204 Diagnosing a Category 6 Return Loss failure # 2 (Water in the cable)
- DTX-CU-205 Diagnosing a Category 6 Return Loss failure #3 (Bad cable)
- DTX-CU-206 Diagnosing a Category 6 Insertion Loss #1 (Lubricant issue)
- DTX-CU-301 "i" next to your Return Loss? It's the 3 dB Rule
- DTX-CU-302 "i" next to your NEXT result? It's the 4 dB Rule
- DTX-CU-303 Short Category 6A links
- DTX-FI-103 Certifying a Duplex LC to LC fiber link
- DTX-FI-104 Certifying a Duplex SC to SC fiber link
- DTX-FI-105 Certifying a Duplex ST to ST fiber link
- DTX-FI-106 Creating a custom fixed loss limit
- DTX-FI-107 Creating a custom connector loss limit
Fiber QuickMap
